ADHESIVE FOR FIXING FOAMED POLYSTYRENE AND XPS PANELS IN THERMAL INSULATION SYSTEMS
increased adhesiveness
good vapour permeability
fast increasing of strength
for ceramic, concrete and silicate elements
FOR INTERNAL AND EXTERNAL USE
|
ATLAS STOPTER K-10 is a cement adhesive for fixing foamed polystyrene boards in ATLAS and ATLAS STOPTER K-10 thermal insulation systems.
ATLAS STOPTER K-10 is a cement adhesive for fixing foamed polystyrene boards in ATLAS STOPTER K-10 thermal insulation systems.
ATLAS STOPTER K-10 can be used on typical mineral substrates such as concrete of all grades, aerated concrete, cement render, cement-lime render, sandstone, and rough surfaces made of bricks, blocks, hollow bricks and other similar ceramic or lime-sand materials. It is suitable for indoor and outdoor use. |
 |
|
| ATLAS STOPTER K-10 is a ready-to-use dry mix of top-quality cement binder, aggregates and modifying agents. It is efficient, convenient and easy to use. It is characterised by very good workability and easy forming as well as increased adhesion, elasticity and vapour permeability. ATLAS STOPTER K-10 is frost- and water-proof. |
|
|
| The substrate should be stable, even and structurally sound i.e. strong enough; it should be free from anything that may weaken adhesion, in particular dust, dirt, lime, oil, fat, wax, remains of emulsion and oil paint. Before work commencement, clean the substrate (water under pressure) and, if necessary, use ATLAS UNI-GRUNT to reduce substrate’s excessive absorptivity. Prime also in case of such substrates as weak cement plasters, cement plasters and walls made of cellular concrete or slag concrete hollow bricks. Fill in larger irregularities and cavities with ATLAS LEVELLING MORTAR or ATLAS PLASTERING MIX. In case of adhesion of foamed polystyrene boards on weak substrates of bearing capacity that can hardly be determined (e.g. dusty, difficult to clean), it is recommended to make an adhesion test. Adhere 10x10 cm foamed polystyrene squares (8÷10 pcs) in various places of the façade and check the bonding after 3 days. If the foamed polystyrene square tears when trying to remove it, substrate resistance can be deemed as sufficient. If the square can be removed with the mortar and substrate layer, it means that the substrate’s structural soundness is insufficient. Further actions in this case e.g. determination of the method to remove the weak layer should be described in a relevant technical project of the insulation. |
|
|
| In order to prepare the adhesive, pour the whole content of the bag into a container with suitable amount of water (in proportion: 5.0÷5.5 l water for 25 kg of dry adhesive) and mix until homogenous. It is best to mix it mechanically, using a drill with a mixer. The mortar is ready to use after 5 minutes and after remixing. It maintains its properties for ca. 3 hours. |
|
|
| Apply ATLAS STOPTER K-10 adhesive on the inside of the board using the “strip-point” method. It consists of preparation of continuous circumferential block (at least 3 cm wide) at the edge of the board and even distribution of 6÷8 patches of 8÷12 cm in diameter on the whole surface. In total, apply so much to cover at least 40% of board surface (after striking down to the substrate, min. 60%) and ensure appropriate board and wall connection. Immediately after application of the mortar on the board, fix the board to the substrate by firm pressing and press down so that mortar thickness under the board does not exceed 1 cm. In case of even and smooth substrates, the adhesive can be evenly distributed using a notched float on the whole board surface to ensure 2÷5 mm layer thickness. ATLAS STOPTER K-10 is a cement adhesive for fixing foamed polystyrene boards in ATLAS and ATLAS STOPTER K-10 thermal insulation systems. Adhesive parameters can be fully applied if it is used with other parts of the system and in accordance with its method of application. The information comprises basic instructions of product application and do not relieve users of responsibility for work in accordance with good construction practice, method of thermal insulation work and OHS regulations. |
|
|
Foamed polystyrene board fixing - from 4.0 do 5.0 kg/m2
The exact amount of adhesive used depends on the substrate (among others, evenness) and used board adhering method. |
|
|
| Drill with mixer, notched float made of steel, trowel Wash the tools with clean water directly after use. Clean the remainder of the set mortar that is difficult to remove with ATLAS SZOP. |
|
|
Paper bags: 25 kg
Pallet: 1050 kg in 25 kg bags |
|
|
| Store and transport in tightly closed bags, in dry conditions (pallets are particularly recommended). Keep dry. Shelf life in conditions complying with the requirements is 12 months from the date on the packaging. |
|
|
| Irritant. Contains cement. Protect skin, eyes and respiratory tract. Keep away from the reach of children. Do not inhale dust. In case of contact with eyes, immediately rinse with plenty of water and seek medical attention. In case of ingestion, immediately seek medical attention and show the packaging or label. |
|
|
Mixing proportions
0.20÷0.22 l of water for 1 kg of adhesive
5.00÷5.50 l of water for 25 kg of adhesive
Pot life – 3 hours
Open time – min. 25 minutes
Adhesion to concrete – min. 0.3 MPa
Adhesion to foamed polystyrene - min. 0.1 MPa
Adhesive preparation temperature – from +5°C to +25°C
Substrate and ambient temperature – from +5°C to +25°C
Temperature resistance – from -20°C to +60°C
Min. thickness of adhesive layer - 2 mm
Max. thickness of adhesive layer - 5 mm
Content of soluble chromium (VI)
in ready-to-use mix - ≤0.0002% |
|
|
The product has been given Technical Approval no. AT-15-4857/2001 by the Building Research Institute and Hygiene Assessment no. HK/B/1197/03/2005 by the National Institute of Hygiene.
ATLAS STOPTER K-10 is a part of thermal insulation systems of external building walls:
ATLAS ETA 06/0081, EC Certificate of Conformity 1488-CPD-0021
ATLAS STOPTER K-10 - AT-15-4947/2004, Certificate of Conformity No. ITB-373/W |
|
