| |
|
2 in 1 - ADHESIVE OF INCREASED ELASTICITY AND ADHESION FOR FIXING MINERAL WOOL BOARDS AND MAKING REINFORCED LAYER IN THERMAL INSULATION SYSTEMS
high adhesiveness
good vapour permeability
excellent elasticity
resistant to cracking
for rough and plastered walls
FOR INTERNAL AND EXTERNAL USE
|
| ATLAS ROKER W-20 is a cement adhesive for fixing façade mineral wool boards and making reinforced layer in ATLAS ROKER thermal insulation system. It can be used on typical mineral substrates such as concrete of all grades, aerated concrete, cement render, cement-lime render, sandstone, and rough surfaces made of bricks, blocks, hollow bricks and other similar ceramic or lime-sand materials. It is also suitable for surfaces covered with strongly adhering layers of façade paint or thin-layer render. It is suitable for indoor and outdoor use. |
 |
|
| ATLAS ROKER W-20 is a ready-to-use dry mix of top-quality cement binder, aggregates and modifying agents. It is efficient, convenient and easy to use. It is characterised by very good workability and easy forming as well as increased adhesion, elasticity and high vapour permeability. ATLAS ROKER W-20 is frost- and water-resistant. |
|
|
| The substrate should be stable, even and structurally sound i.e. strong enough; it should be free from anything that may weaken adhesion, in particular dust, dirt, lime, oil, fat, wax, remains of emulsion and oil paint. Wash the whole wall with water under pressure. Before work commencement, prime the substrate using ATLAS UNI-GRUNT. Prime also in case of such substrates as weak cement plasters, cement plasters and walls made of cellular concrete or slag concrete hollow bricks. Fill in larger irregularities and cavities with ATLAS LEVELLING MORTAR or ATLAS PLASTERING MIX. In case of adhesion of mineral wool boards on weak substrates of bearing capacity that can hardly be determined (e.g. dusty, difficult to clean), it is recommended to make an adhesion test. Adhere 10x10 cm insulation material squares (8÷10 pcs) in various places of the façade and check the bonding after 3 days. If the mineral wool square tears when trying to remove it, substrate resistance can be deemed as sufficient. If the square can be removed with the adhesive and substrate layer, it means that the substrate is insufficiently structurally sound. Further actions in this case e.g. determination of the method to remove the weak layer should be described in a relevant technical project of the insulation. |
|
|
In order to prepare the adhesive, pour the whole content of the bag into a container with suitable amount of water (in proportion: 5.50÷6.25 l water for 25 kg of dry mortar) and mix until homogenous.
It is best to mix it mechanically, using a drill with a mixer. The adhesive is ready to use after 5 minutes and after remixing. It maintains its properties for ca. 2 hours. |
|
|
Board fixing
In ATLAS ROKER thermal insulation system, it is possible to use mineral wool boards of both disordered (so-called front boards) and ordered fibrous structure (so-called lamella boards). Float board surface with a thin layer of the mortar and after initial setting apply the proper layer using the “strip-point” method. The width of circumferential block around the edge of the board should be at least 3 cm. On the remaining surface, distribute evenly 6÷8 patches of 8÷12 cm in diameter. In total, apply so much to cover at least 40% of board surface (after striking down to the substrate, min. 60%) and ensure appropriate board and wall connection. In case of even and smooth substrates, it is allowable to distribute the mortar evenly with a notched trowel on the whole board. Immediately after application of the adhesive on the board, fix the board to the substrate and press down to required position. Begin fixing mechanical fasteners not earlier than 1 day after board fixing. Use the number of dowels with a galvanised metal arbour specified in the technical thermal insulation project, min. 8 pcs/m2.
Reinforced layer preparation
Begin preparation of the reinforced layer not earlier than 3 days after board fixing. The reinforced layer consists of a reinforcing mesh made of glass fibre set in ATLAS ROKER W-20.
Apply a thin layer of ATLAS ROKER W-20 on fixed boards.
After initial setting, apply another adhesive layer with a smooth float made of steel using 2/3 of the final quantity and distribute it evenly with a notched float. Set previously cut mesh strip in the adhesive. First press it down in several spots in the applied adhesive and then carefully cover it with the adhesive using a notched float so that the mesh is not visible. Then, apply the remaining 1/3 of the adhesive and carefully smooth the surface. If there are any irregularities after smoothing, grind them off as they may prevent correct plaster coating preparation due to its small thickness (2÷3 mm). After the adhesive drying time (ca. 3 days), external render can be applied. ATLAS ROKER W-20 is a part of ATLAS ROKER thermal insulation system. Mortar parameters can be fully applied if it is used with other parts of the system and in accordance with its method of application. The information comprises basic instructions of product application and do not relieve users of responsibility for work in accordance with good construction practice and OHS regulations. |
|
|
Mineral wool insulation board fixing - from 4.5 do 5.5 kg/m2
Reinforced layer preparation – from 5.5 to 6.5 kg/m2
The exact amount of adhesive used depends on the substrate (among others, evenness) and used board adhering method. |
|
|
| Drill with mixer, smooth and notched or float made of steel, trowel. Wash the tools with clean water directly after use. Clean the remainder of the set mortar that is difficult to remove with ATLAS SZOP. |
|
|
Paper bags: 25 kg
Pallet: 1050 kg in 25 kg bags |
|
|
| Store and transport in tightly closed bags, in dry conditions (pallets are particularly recommended). Keep dry. Shelf life in conditions complying with the requirements is 12 months from the date on the packaging. |
|
|
| Irritant. Contains cement. Protect skin, eyes and respiratory tract. Keep away from the reach of children. Do not inhale dust. In case of contact with eyes, immediately rinse with plenty of water and seek medical attention. In case of ingestion, immediately seek medical attention and show the packaging or label. |
|
|
Mixing proportions
0.22÷0.25 l of water for 1 kg of adhesive
5.50÷6.25 l of water for 25 kg of adhesiver
Pot life – 2 hours
Open time – min. 30 minutes
Adhesion to concrete – min. 0.6 MPa
Adhesion to mineral wool – min. 0.015 MPa
Adhesive preparation temperature – from +5°C to +25°C
Substrate and ambient temperature – from +5°C to +25°C
Temperature resistance – from +20°C to +60°C
Min. thickness of adhesive layer - 4 mm
Max. thickness of adhesive layer - 6 mm
Content of soluble chromium (VI)
in ready-to-use mix - ≤0.0002% |
|
|
The product has been given Technical Approval no. AT-15-2927/03 by the Building Research Institute and Hygiene Certificate no. HK/B/0914/04/2006 by the National Institute of Hygiene.
ATLAS ROKER W-20 is a part of ATLAS ROKER thermal insulation systems of external building walls:
- ETA 06/0173, EC Certificate of Conformity 1488-CPD-0036 - AT-15-2930/2004. |
|
|
|
|
|
|
|
